FT232 USB UART IC
₹303.00
Features of FT232
-
Single chip USB to asynchronous serial data transfer interface.
-
Entire USB protocol handled on the chip. No USB specific firmware programming required.
-
Fully integrated 1024 bit EEPROM storing device descriptors and CBUS I/O configuration.
-
Fully integrated USB termination resistors.
-
Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.
-
Data transfer rates from 300 baud to 3 Mbaud (RS422, RS485, RS232) at TTL levels.
-
128 byte receive buffer and 256 byte transmit buffer utilising buffer smoothing technology to allow for high data throughput.
1000 in stock (can be backordered)
Reviews (0)
Shipping & Delivery
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Related products
CM8870-PI
The CM8870PI provides full DTMF receiver capability by integrating both the bandsplit filter and digital decoder functions into a single 18-pin DIP. The filter section uses a switched capacitor technique for both high and low group filters and dial tone rejection. The CM8870 decoder uses digital counting techniques for the detection and decoding of all 16 DTMF tone pairs into a 4-bit code. This DTMF receiver minimizes external component count by providing an on-chip differential input ampli-fier, clock generator, and a latched three state interface bus. The on-chip clock generator requires only a low cost TV crystal or ceramic resonator as an external component.
LM2596S 3.3 Volts fixed Voltage Converter (TO-263)
The LM2596S series of regulators are monolithic integrated circuits that provide all the active functions for a step-down (buck) switching regulator, capable of driving a 1 Ampere load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3V, 5V, 12V, and an adjustable output version.
Requiring a minimum number of externalcomponents, these regulators are simple to use andinclude internal frequency compensation, and a fixed frequency oscillator.
MAX485 IC
Each part contains one driver and one receiver. The driver slew rates of the MAX485 is not limited, allowing them to transmit up to 2.5Mbps. All parts operate from a single 5V supply.The driver is short-circuit current limited and? protected against excessive power dissipation by thermal shutdown circuitry that places the driver outputs into a high-impedance state. The receiver input has a fail-safe feature that guarantees a logic-high output if the input is open circuit. The MAX485 is designed for half-duplex applications.
MAX485ESA RS422 RS485 Interface IC
MAX485 is a low power transceivers for RS485 and RS422 communication. MAX485 contains one driver and one receiver. The driver slew rates of the MAX485 are not limited, allowing it to transmit up to 2.5Mbps.
These transceivers draw between 120?A and 500?A of supply current when unloaded or fully loaded with disabled drivers.?MAX485ESA RS422 RS485 IC?operates from a single 5V supply. Drivers are short circuit current limited and are protected against excessive power dissipation by thermal shutdown circuitry that places the driver outputs into a high-impedance state. The receiver input has a fail-safe feature that guarantees a logic-high output if the input is open circuit.
MCP2515 CAN CONTROLLER
Microchip Technology?s MCP2515 is a stand-alone?Controller Area Network (CAN) controller that?implements the CAN specification, version 2.0B. It is?capable of transmitting and receiving both standard?and extended data and remote frames. The MCP2515?has two acceptance masks and six acceptance filters?that are used to filter out unwanted messages, thereby?reducing the host MCU?s overhead. The MCP2515 CAN Controller?interfaces with microcontrollers (MCUs) via an industry?standard Serial Peripheral Interface (SPI).
MCP2551 CAN transceiver
The?MCP2551?is a high-speed?Controller Area Network?(CAN), fault-tolerant?device that serves as the interface between a?CAN?protocol controller?and the physical bus. The MCP2551?device provides differential transmit and receive?capability for the CAN protocol controller, and is fully?compatible with the ISO-11898 standard, including 24V?requirements. It will operate at speeds of up to 1 Mb/s.
Typically, each node in a CAN system must have a?device to convert the digital signals generated by a?CAN controller to signals suitable for transmission over?the bus cabling (differential output). It also provides a?buffer between the CAN controller and the high-voltage?spikes that can be generated on the CAN bus by?outside sources (EMI, ESD, electrical transients, etc.).
Reviews
There are no reviews yet.