MCP2510 CAN Controller
₹203.00
The MCP2510 provides immediate CAN support across the entire breadth of Microchip?s 100 PICmicro? microcontrollers, providing a seamless migration path and maximum design flexibility for CAN designs. The?MCP2510 CAN Controller?contains on-board features, such as interrupt capability, message masking and filtering, message prioritization, multi-purpose I/O pins, and multiple transmit/receive buffers which significantly offload the microcontroller overhead required to handle CAN message traffic. Applications for the MCP2510 include motor control, smoke detectors, CO detectors, sensors, meters, automotive electronics, climate control and instrument clusters.
1000 in stock


MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisqueĀ vestibulum amet elit ut volutpat.
Related products
MCP2200 USB 2.0 to UART Protocol Converter with GPIO
MAX3232-SMD RS-232 Line Driver
MAX3232 device?consists of two line drivers, two line receivers, and a dual charge-pump circuit with ?15-kV ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. The devices operate at data signalling rates up to 250 kbit/s and a maximum of 30-V/?s driver output slew rate.
CH376S USB Read Write IC
CH376?is used as file manage control chip, used to MCU system read/write file in USB Flash Drive ?or SD card.
CH376 supports?USB-Device Mode?and?USB-HOST Mode. Set the basic firmware of?USB communication protocol in the inner. It is also set firmware of special communication protocol to ?deal with Mass-Storage devices, communication interface firmware of SD card, FAT16, FAT32 and?FAT12 file system manage firmware in the inner.
LM2596S Adjustable Voltage Converter (TO-263)
AM26C31 Differential Line Receiver (SOIC)
The AM26C31 is an improved replacement for?AM26LS31 IC.?The AM26C31 device is a quadruple differential line receiver for balanced or unbalanced digital data transmission. The enable function is common to all four receivers and offers a choice of active-high or active-low input. The 3-state outputs permit connection directly to a busorganized system. Fail-safe design specifies that if the inputs are open, the outputs always are high. The AM26C31 devices are manufactured using a BiCMOS process, which is a combination of bipolar and CMOS transistors
LM2596S 3.3 Volts fixed Voltage Converter (TO-263)
P6KE150CA TVS Diode
The P6KE Series diodes is designed specifically to save your circuit from this sudden spike in voltage. P6KE Series diode are a very good?Transient Voltage Suppressor?(TVS) Diode. P6KE TVS Diodes are rated at 600 Watts and protects the?sensitive electronic devices?from the voltage spikes induced on circuit.
The characteristic of a?P6KE TVS diode?is that it respond to over voltages faster than other common overvoltage protection components such as varistors or gas discharge tubes. This makes?TVS diodes?useful for protection against very fast and often damaging voltage spikes.
FT232 USB UART IC
Features of FT232
-
Single chip USB to asynchronous serial data transfer interface.
-
Entire USB protocol handled on the chip. No USB specific firmware programming required.
-
Fully integrated 1024 bit EEPROM storing device descriptors and CBUS I/O configuration.
-
Fully integrated USB termination resistors.
-
Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.
-
Data transfer rates from 300 baud to 3 Mbaud (RS422, RS485, RS232) at TTL levels.
-
128 byte receive buffer and 256 byte transmit buffer utilising buffer smoothing technology to allow for high data throughput.
Reviews
There are no reviews yet.