CM8870-PI
₹30.00
The CM8870PI provides full DTMF receiver capability by integrating both the bandsplit filter and digital decoder functions into a single 18-pin DIP. The filter section uses a switched capacitor technique for both high and low group filters and dial tone rejection. The CM8870 decoder uses digital counting techniques for the detection and decoding of all 16 DTMF tone pairs into a 4-bit code. This DTMF receiver minimizes external component count by providing an on-chip differential input ampli-fier, clock generator, and a latched three state interface bus. The on-chip clock generator requires only a low cost TV crystal or ceramic resonator as an external component.
149 in stock (can be backordered)
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Related products
CH340g USB to TTL IC
As of now the CH340g is the cheapest USB to TTL IC in the market with very easy to solder foot print it has solder pitch of 1.27mm and SOIC16 package.
The?CH340 IC?does exactly what you would expect them to do: a full-speed USB device that emulates a standard serial interface, with speeds from 50bps to 2Mpbs. The chip supports 5V and 3.3V, and all the weird modem lines are supported.
Now a days lots of Node MCU, Arduino Nano and USB to TTL Converter Modules have been using this IC.
FT232 USB UART IC
Features of FT232
-
Single chip USB to asynchronous serial data transfer interface.
-
Entire USB protocol handled on the chip. No USB specific firmware programming required.
-
Fully integrated 1024 bit EEPROM storing device descriptors and CBUS I/O configuration.
-
Fully integrated USB termination resistors.
-
Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.
-
Data transfer rates from 300 baud to 3 Mbaud (RS422, RS485, RS232) at TTL levels.
-
128 byte receive buffer and 256 byte transmit buffer utilising buffer smoothing technology to allow for high data throughput.
LM2596S 3.3 Volts fixed Voltage Converter (TO-263)
MAX232 TTL to RS232 IC
MAX232 is a communication IC. It is used to convert TTL Signals to RS232 Signal and vice versa.?MAX232?provides RS-232 voltage level outputs (approx. ? 7.5 V) from a single 5 V supply via on-chip charge pumps and external capacitors. This makes it useful for implementing RS-232 in devices that otherwise do not need any voltages outside the 0 V to 5 V range, as power supply design does not need to be made more complicated just for driving the RS-232 in this case.
The receivers reduce RS-232 inputs (which may be as high as ? 25 V), to standard 5 V TTL levels. These receivers have a typical threshold of 1.3 V, and a typical hysteresis of 0.5 V.
MAX3232 RS-232 Line Driver
The?MAX3232 device?consists of two line drivers, two line receivers, and a dual charge-pump circuit with ?15-kV ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector.? The devices operate at data signaling rates up to 250 kbit/s and a maximum of 30-V/?s driver output slew rate.
MAX485ESA RS422 RS485 Interface IC
MAX485 is a low power transceivers for RS485 and RS422 communication. MAX485 contains one driver and one receiver. The driver slew rates of the MAX485 are not limited, allowing it to transmit up to 2.5Mbps.
These transceivers draw between 120?A and 500?A of supply current when unloaded or fully loaded with disabled drivers.?MAX485ESA RS422 RS485 IC?operates from a single 5V supply. Drivers are short circuit current limited and are protected against excessive power dissipation by thermal shutdown circuitry that places the driver outputs into a high-impedance state. The receiver input has a fail-safe feature that guarantees a logic-high output if the input is open circuit.
Reviews
There are no reviews yet.