AM26C32 Differential Line Receiver (SOIC)
₹61.72
AM26C32 is an improved replacement for?AM26LS32 IC. The AM26C32 device is a quadruple differential line receiver for balanced or unbalanced digital data transmission. The enable function is common to all four receivers and offers a choice of active-high or active-low input. The 3-state outputs permit connection directly to a busorganized system. Fail-safe design specifies that if the inputs are open, the outputs always are high. The AM26C32 devices are manufactured using a BiCMOS process, which is a combination of bipolar and CMOS transistors.
1000 in stock (can be backordered)
Reviews (0)
Shipping & Delivery
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Related products
CH340g USB to TTL IC
As of now the CH340g is the cheapest USB to TTL IC in the market with very easy to solder foot print it has solder pitch of 1.27mm and SOIC16 package.
The?CH340 IC?does exactly what you would expect them to do: a full-speed USB device that emulates a standard serial interface, with speeds from 50bps to 2Mpbs. The chip supports 5V and 3.3V, and all the weird modem lines are supported.
Now a days lots of Node MCU, Arduino Nano and USB to TTL Converter Modules have been using this IC.
MAX3232-SMD RS-232 Line Driver
MAX3232 device?consists of two line drivers, two line receivers, and a dual charge-pump circuit with ?15-kV ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. The devices operate at data signalling rates up to 250 kbit/s and a maximum of 30-V/?s driver output slew rate.
MAX485 IC
Each part contains one driver and one receiver. The driver slew rates of the MAX485 is not limited, allowing them to transmit up to 2.5Mbps. All parts operate from a single 5V supply.The driver is short-circuit current limited and? protected against excessive power dissipation by thermal shutdown circuitry that places the driver outputs into a high-impedance state. The receiver input has a fail-safe feature that guarantees a logic-high output if the input is open circuit. The MAX485 is designed for half-duplex applications.
MCP2515 CAN CONTROLLER
Microchip Technology?s MCP2515 is a stand-alone?Controller Area Network (CAN) controller that?implements the CAN specification, version 2.0B. It is?capable of transmitting and receiving both standard?and extended data and remote frames. The MCP2515?has two acceptance masks and six acceptance filters?that are used to filter out unwanted messages, thereby?reducing the host MCU?s overhead. The MCP2515 CAN Controller?interfaces with microcontrollers (MCUs) via an industry?standard Serial Peripheral Interface (SPI).
MCP2551 CAN transceiver
The?MCP2551?is a high-speed?Controller Area Network?(CAN), fault-tolerant?device that serves as the interface between a?CAN?protocol controller?and the physical bus. The MCP2551?device provides differential transmit and receive?capability for the CAN protocol controller, and is fully?compatible with the ISO-11898 standard, including 24V?requirements. It will operate at speeds of up to 1 Mb/s.
Typically, each node in a CAN system must have a?device to convert the digital signals generated by a?CAN controller to signals suitable for transmission over?the bus cabling (differential output). It also provides a?buffer between the CAN controller and the high-voltage?spikes that can be generated on the CAN bus by?outside sources (EMI, ESD, electrical transients, etc.).
Reviews
There are no reviews yet.