ADA4851-2YRMZ
FEATURES
130 MHz high speed, 3 dB bandwidth, 375 V/s slew rate, 55 ns settling time to 0.1%
Outstanding video specs
11 MHz, 0.1 dB flatness
Gain on differential: 0.08%
0.09? differential phase
Completely defined for +3 V, +5 V, and 5 V supply
Rail-to-rail transmission
The output swings to within 60 millivolts of each rail.
0.6 mV low voltage offset
Supply voltage range: 3 V to 10 V
Low power consumption: 2.5 mA/amplifier
Power-saving mode
SOT-23-6, TSSOP-14, and MSOP-8 space-saving packages are available.
APPLICATIONS
Video for consumers
Professional videography
Switchers for video
Filters that are active
ADC0804 8-Bit Analog to Digital A/D Converter IC DIP-20 Package
The ADC0804 are CMOS 8-Bit, successive approximation A/D converters which use a modified potentiometric ladder and are designed to operate with the 8080A control bus via three-state outputs. These converters appear to the processor as memory locations or I/O ports, and hence no interfacing logic is required.
ADC0808 8-Bit A/D Converter with 8-Channel Multiplexer IC DIP-28 Package
ADC0808N
The ADC0808, ADC0809 data acquisition component
2? Easy Interface to All Microprocessors
is a monolithic CMOS device with an 8-bit analog-to-
? Operates Ratiometrically or with 5 VDC or digital converter, 8-channel multiplexer and
Analog Span Adjusted Voltage Reference microprocessor compatible control logic. The 8-bit
? No Zero or Full-Scale Adjust Required A/D converter uses successive approximation as the
conversion technique. The converter features a high ? 8-Channel Multiplexer with Address Logic
impedance chopper stabilized comparator, a 256R
? 0V to VCC Input Range voltage divider with analog switch tree and a
? Outputs meet TTL Voltage Level Specifications successive approximation register. The 8-channel
? ADC0808 Equivalent to MM74C949 multiplexer can directly access any of 8-single-ended
analog signals
ADC0809 8-Bit A/D Converter with 8-Channel Multiplexer IC DIP-28 Package
ADC0838CIWM
The ADC0831 series are 8-bit successive
Address Logic approximation A/D converters with a serial I/O and
configurable input multiplexers with up to 8 channels. ? Shunt Regulator Allows Operation with High
The serial I/O is configured to comply with the TI Voltage Supplies MICROWIRE serial data exchange standard for easy
? 0V to 5V Input Range with Single 5V Power interface to the COPS family of processors, and can
Supply interface with standard shift registers or ?Ps.
? Remote Operation with Serial Digital Data Link The 2-, 4- or 8-channel multiplexers are software
? TTL/MOS Input/Output Compatible configured for single-ended or differential inputs as
? 0.3 well as channel assignment. in. Standard Width, 8-, 14- or 20-Pin PDIP
Package The differential analog voltage input allows increasing
? 20 Pin PLCC Package (ADC0838-N Only) the common-mode rejection and offsetting the analog
zero input voltage value. In addition, the voltage ? SOIC Package
reference input can be adjusted to allow encoding
any smaller analog voltage span to the full 8 bits of
resolution
ADE7763ARSZ
phase matching between the current and the voltage channels.
The ADE7763 provides a serial interface to read data and a
pulse output frequency (CF) that is proportional to the active
power. Various system calibration features such as channel
offset correction, phase calibration, and power calibration
ensure high accuracy. The part also detects short duration, low
or high voltage variations.
The positive-only accumulation mode gives the option to
accumulate energy only when positive power is detected. An
internal no-load threshold ensures that the part does not exhibit
any creep when there is no load. The zero-crossing output (ZX)
produces a pulse that is synchronized to the zero-crossing point
of the line voltage. This signal is used internally in the line cycle
active and apparent energy accumulation modes, which enables
faster calibration
