MT8870 IC – DTMF Decoder IC

Features? of? L30960-N5130-B100

• LTE (2x2 DL-MIMO; FDD 3GPP Release 9)
• 3GPP Release 8; UMTS/HSPA (FDD); Rx diversity
• 3GPP Release 6; DARP/SAIC; GSM/GPRS/EDGE
• SIM Application Toolkit, version 99 of the 3GPP
• Using AT instructions to control (Hayes, TS 27.007, TS 27.005)
• 3.3 to 4.2 V supply voltage range, especially tuned for low power usage
• Size: 40, 32, and 2,8 mm
• Range of Operation Temperature: -40 ?C to +95 ?
• Compliant with RoHS, RED, and REACH, EuP assistance

  Special Features L30960-N5130-B100

• The USB 2.0/3.0 interface provides several composite modes and a mode that is compatible with Linux and Mac.
• USB-based firmware update

 

Benefits and features of BGU7005

• Covers the entire GNSS L1 range, 1559 to 1610 MHz
• Noise figure (NF) is equal to 0.85 dB.
• Increase 16.5 dB
• A lot of input Pi(1dB), or 1 dB compression point, is 11 dBm.
• High IP3i out of band of 9 dBm
• 1.5 to 3.1 volts is the supply voltage.
• Consumption of current in power-saving mode is 1 A.
• Optimized performance at 4.5 mA, a low supply current
• Output matching that is integrated
• Only needs one supply decoupling capacitor and one input matching inductor.
• Decoupled DC input and output
• All pins have ESD protection (HBM > 2 kV).
• Temperature-stabilized bias included for simple design
• Small leadless 6-pin package 1.45 mm, 1 mm, and 0.5 mm
• Transit frequency of 110 GHz using SiGe:C technology

HT12D is a decoder integrated circuit that belongs to 212 series of decoders. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc. It is mainly provided to interface RF and infrared circuits.? They are paired with 212 series of encoders. The chosen pair of encoder/decoder should have same number of addresses and data format.In simple terms, HT12D converts the serial input into parallel outputs. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins. The serial input data is compared with the local addresses three times continuously. The input data code is decoded when no error or unmatched codes are found. A valid transmission in indicated by a high signal at VT pin. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. The data on 4 bit latch type output pins remain unchanged until new is received. Datasheet of ht12d decoder ic

Features of CC2650F128RHB

• Microprocessor - Strong ARM Cortex-M3 processor - 142 for EEMBC CoreMark? - Maximum Clock Speed of 48 MHz - 128 KB of programmable in-system flash - Cache: 8KB of SRAM - 20KB of SRAM with ultra-low leakage. - JTAG and 2-Pin cJTAG Debugging - Facilitates Over-The-Air Upgrade (OTA)
• Sensor Controller with Ultralow Power - Can Operate Independently of the Rest of the System - 16-Bit architecture - 2KB of SRAM with extremely minimal leakage for code and data.
• Packages Compliant with RoHS - RSM VQFN32, 4-mm x?4-mm (10 GPIOs) - RHB VQFN32, 5-mm x?5-mm (15 GPIOs) - RGZ VQFN48, 7-mm x?7-mm (31 GPIOs)
• Peripherals - Any GPIO Can Be Used to Route All Digital Peripheral Pins - Four modules for general-purpose timers. - 200 ksamples/s, 8-Channel Analog MUX, 12-Bit ADC - Comparator for Continuous Time - Ultralow-Power Analog Comparer -Modifiable Current Source - UART - Clock in Real Time (RTC) - Security Module AES-128 - The TRNG (True Random Number Generator) (TRNG) - Depending on the package option, 10, 15, or 31 GPIOs - Eight capacitive-sensing buttons are supported. - Temperature sensor built-in
• ?Outside System - Internal On-Chip DC-DC Converter - Low Number of External Components - Complete Integration With Simple LinkTM CC2590 and CC2592 Range Extenders - Compatible with the CC13xx pin of Simple Link - VQFN Packages in 4-mm x 4-mm and 5-mm x 5-mm sizes
• Small Power - Broad Supply Voltage Spectrum ? In normal use, 1.8 to 3.8 V ? 1.7 to 1.95 V in external regulator mode -5.9 mA Active-Mode RX - Active-Mode TX: 6.1 mA at 0 dBm - 9.1 mA for Active-Mode TX at +5 dBm -MCU in Active Mode: 61 A/MHz -48.5 CoreMark/mA for Active-Mode MCU -8.2 A/MHz Active-Mode Sensor Controller - RAM/CPU Retention and RTC Running: 1 A in Standby - Shutdown 100 nanoamperes (Wake Up on External Events)

Application of CC2650F128RHB

• Electronics for consumers  
• Cellular Phone Accessory  
• Sports and exercise gear  
• Applications for HID  
• Building and Home Automation
• Lighting Management  
• Security and Alarm  
• Labeling Electronic Shelves  
• Nearby tags  
• Health  
• Wireless controls  
• Sensor Networks, Wireless