LPC1768 Microcontrollers – MCU
₹1,500.00
CPU frequencies of up to 100 MHz are supported by the LPC1768/67/66/65/64/63. The LPC1769 can run at CPU speeds of up to 120 MHz. The Arm Cortex-M3 CPU has a three-stage pipeline and a Harvard architecture, with separate local instruction and data buses and a third bus for peripherals. An inbuilt prefetch unit that facilitates speculative branching is also included in the Arm Cortex-M3 CPU.The LPC1769/68/67/66/65/64/63’s peripheral complement includes up to 512 kB of flash memory, 64 kB of data memory, Ethernet MAC, USB Device/Host/OTG interface, 8-channel general-purpose DMA controller, 4 UARTs, 2 CAN channels, 2 SSP controllers, SPI interface, 3 I2C-bus interfaces, 2-input plus 2-output I2S-bus interface, 8-channel 12-bit A
Description
Features – LPC1768 Microcontrollers – MCU
- Arm??Cortex-M3 processor, running at frequencies of up to 100 MHz
- Arm Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC)
- Up to 512 kB on-chip flash programming memory
- Up to 64 kB On-chip SRAM
- In-System Programming (ISP) and In-Application Programming (IAP)
- Eight-channel General-Purpose DMA controller (GPDMA)
- Ethernet MAC with RMII interface and dedicated DMA controller
- USB 2.0 full-speed device/Host/OTG controller
- Four UARTs with fractional baud rate generation, internal FIFO, and DMA support
- CAN 2.0B controller with two channels
- SPI controller with synchronous, serial, full-duplex communication
- Two SSP controllers with FIFO and multi-protocol capabilities
- Three enhanced I2C bus interfaces
- I2S (Inter-IC Sound) interface
- 70 General Purpose I/O (GPIO) pins with configurable pull-up/down resistors
- 12-bit/8-ch Analog/Digital Converter (ADC) with conversion rates up to 200 kHz
- 10-bit Digital/Analog Converter (DAC) with dedicated conversion timer and DMA
- Four general-purpose timers/counters
- One motor control PWM with support for three-phase motor control
- Quadrature encoder interface that can monitor one external quadrature encoder
- One standard PWM/timer block with external count input
- Low power RTC with a separate power domain and dedicated oscillator
- Watchdog Timer (WDT)
- Arm Cortex-M3 system tick timer, including an external clock input option
- Repetitive interrupt timer provides programmable and repeating timed interrupts
- Each peripheral has its own clock divider for further power savings
- Standard JTAG test/debug interface for compatibility with existing tools
- Integrated PMU (Power Management Unit)
- Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down
- Single 3.3 V power supply (2.4 V to 3.6 V)
- Four external interrupt inputs configurable as edge/level sensitive
- Non-maskable Interrupt (NMI) input
- Wake-up Interrupt Controller (WIC)
- Processor wake-up from Power-down mode via any interrupt
- Brownout detect with separate threshold for interrupt and forced reset
- Power-On Reset (POR)
- Crystal oscillator with an operating range of 1 MHz to 25 MHz
- 4 MHz internal RC oscillator trimmed to 1 % accuracy
- Code Read Protection (CRP) with different security levels
- Unique device serial number for identification purposes
Target Applications – LPC1768 Microcontrollers – MCU
- eMetering
- Lighting
- Industrial networking
- Alarm systems
- White goods
- Motor control
Reviews (0)
Shipping & Delivery
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Related products
APQ8009-0-504NSP-TR-01-1-AA
Features of APQ8009
- Adreno 304 GPU 3D graphics accelerator with support for the newest API (up to 456 MHz)
- Battery-friendly audio/video use cases are provided by the Hexagon 536 DSP.
- Heterogeneous architecture features a quad-core, 32-bit Arm Cortex-A7 CPU with a maximum clock speed of 1.3GHz.
- Made using the cutting-edge 28 nm LP CMOS manufacturing method
- Integrated Bluetooth 4.1 low energy, GPS, and 802.11a/b/g/n support
- Offers specialized support for popular codecs in the market as well as additional multimedia formats to enable carrier deployments worldwide.
- An international network of QTI suppliers, users, programmers, and embedded device OEMs
- Wireless Speakers
- Cellular cameras
- Audiovisual Equipment
- Smart home technology
- Smart Home Devices
- Digital helpers
ATMEGA48PA-PU Microcontroller
Microchip ATMEGA48PA-PU, 8bit AVR Microcontroller, ATmega, 20MHz, 4 kB Flash, 28-Pin PDIP
The ATmega48A/PA/88A/PA/168A/PA/328/P is a low power, CMOS 8-bit microcontrollers based on the AVR? enhanced RISC architecture. By executing instructions in a single clock cycle, the devices achieve CPU throughput approaching one million instructions per second (MIPS) per megahertz, allowing the system designer to optimize power consumption versus processing speed. Part Number: ATMEGA48PA-PU Manufacturer: Microchip Technology Description: IC MCU 8BIT 4KB FLASH 28DIP Detailed Description: AVR AVR? ATmega Microcontroller IC 8-Bit 20MHz 4KB (2K x 16) FLASH 28-PDIP atmega48pa-pu datasheet
LM7812 IC – 7812 voltage regulator (12V)
The LM7812 series of three terminal positive regulators are available in the TO-220 package and with several fixed output voltages, making them useful in a wide range of applications. Each type employs internal current limiting, thermal shut down and safe operating area protection, making it essentially indestructible. If adequate heat sinking is provided, they can deliver over 1A output current. Although designed primarily as fixed voltage regulators, these devices can be used with external components to obtain adjustable voltages and currents.
MCP3208-BI/P
? 12-bit resolution
? ? 1 LSB max DNL
? ? 1 LSB max INL (MCP3204/3208-B)
? ? 2 LSB max INL (MCP3204/3208-C)
? 4 (MCP3204) or 8 (MCP3208) input channels
? Analog inputs programmable as single-ended or
pseudo-differential pairs
? On-chip sample and hold
? SPI serial interface (modes 0,0 and 1,1)
? Single supply operation: 2.7V - 5.5V
? 100 ksps max. sampling rate at VDD = 5V
? 50 ksps max. sampling rate at VDD = 2.7V
? Low power CMOS technology:
- 500 nA typical standby current, 2 ?A max.
- 400 ?A max. active current at 5V
? Industrial temp range: -40?C to 85?C
? Available in PDIP, SOIC and TSSOP packages
MCP602-I/P
? Single-Supply: 2.7V to 6.0V
? Rail-to-Rail Output
? Input Range Includes Ground
? Gain Bandwidth Product: 2.8 MHz (typical)
? Unity-Gain Stable
? Low Quiescent Current: 230 ?A/amplifier (typical)
? Chip Select (CS): MCP603 only
? Temperature Ranges:
- Industrial: -40?C to 85?C
- Extended: -40?C to 125?C
? Available in Single, Dual, and Quad
MCP604-I/P
The Microchip Technology Inc. MCP601/1R/2/3/4
family of low-power operational amplifiers (op amps)
are offered in single (MCP601), single with Chip Select
(CS) (MCP603), dual (MCP602), and quad (MCP604)
configurations. These op amps utilize an advanced
CMOS technology that provides low bias current, highspeed operation, high open-loop gain, and rail-to-rail
output swing. This product offering operates with a
single supply voltage that can be as low as 2.7V, while
drawing 230 ?A (typical) of quiescent current per
amplifier. In addition, the common mode input voltage
range goes 0.3V below ground, making these
amplifiers ideal for single-supply operation.
These devices are appropriate for low power, battery
operated circuits due to the low quiescent current, for
A/D convert driver amplifiers because of their wide
bandwidth or for anti-aliasing filters by virtue of their low
input bias current.
PIC16F887 Microcontroller
PIC16F887 Microcontroller?is an 8-bit microcontroller
PIC16F887 Microcontroller?is an 8-bit microcontroller designed with RSIC CPU technology, which helps the microcontroller to give the maximum output using less power. It has a total of 40-pins and all these pins come in multiple packages to solve the requirement of small and modern circuits. 44 pin QFN and TQFP packages are also available. PIC16F887 provides all the modern protocol to the developers and due to its multiple pins, the most protocol can be followed at the same time without effecting others. The PIC has multiple usages with the industry and at commercial level due to its multiple A/D channels and internal clock.- LED projects using PIC16F877A -? https://www.youtube.com/watch?v=swepVjQxUTo
STM8S003F3P6
STM8S003F3P6 - The STM8S003F6 value line 8-bit microcontrollers offer 8 Kbytes of Flash program memory, plus integrated true data EEPROM. They are referred to as low-density devices in the STM8S microcontroller family reference manual (RM0016). The STM8S003F3 value line devices provide the following benefits: performance, robustness, and reduced system cost. Device performance and robustness are ensured by true data EEPROM supporting up to 100000 write/erase cycles, advanced core and peripherals made in state-of-the-art technology at 16 MHz clock frequency, robust I/Os, independent watchdogs with separate clock source, and a clock security system. The system cost is reduced thanks to a high system integration level with internal clock oscillators, watchdog, and brown-out reset.
Reviews
There are no reviews yet.