MAX320CSA
The MAX320 series, powered from ?5V supplies, offers
35? max on-resistance (RON), 2? max matching
between channels, and 4? max RON flatness.
These switches also offer 5pC max charge injection
and a minimum of 2000V ESD protection per Method
3015.7.
For equivalent devices specified for single-supply operation, see the MAX323/MAX324/MAX325 data sheet.
For quad versions of these switches
MAX3221CAE
The MAX3221/MAX3223/MAX3243 achieve 1?A supply
current with Maxim?s revolutionary AutoShutdown?
feature. When the MAX3221/MAX3223/MAX3243 do not
sense a valid signal level on their receiver inputs, the onboard power supply and drivers shut down. This occurs
if the RS-232 cable is disconnected or if the transmitters
of the connected peripheral are turned off. The system
turns on again when a valid level is applied to any RS-232
receiver input.
The MAX3221/MAX3223/MAX3243 require only 0.1?F
capacitors in 3.3V operation, and can operate from input
voltages ranging from 3.0V to 5.5V
MAX323ESA
Low On-Resistance (RON), 60? max (33? typ)
? RON Matching Between Channels <2?
? RON Flatness <6? Max
? Guaranteed Charge Injection <5pC
? Single-Supply Operation ( 2.7V to 16V)
? Low Power Consumption, <5?W
? Low Leakage Current Over Temperature,
<2.5nA at 85?C
? Fast Switching: tON <150ns, tOFF <100ns
? Guaranteed Break-Before-Make (MAX325 only)
? TTL/CMOS Logic Compatible
MAX335CWG
These CMOS switches can operate continuously with
power supplies ranging from ?4.5V to ?20V and handle
rail-to-rail analog signals. Upon power-up, all switches are
off, and the internal serial and parallel shift registers are
reset to zero. The MAX335 is equivalent to two DG211
quad switches but controlled by a serial interface.
The interface is compatible with the Motorola SPI interface
standard. Functioning as a shift register, this serial interface
allows data (at DIN) to be locked in synchronous with the
rising edge of clock (SCLK). The shift register?s output
(DOUT) enables several MAX335s to be daisy chained
MAX4216ESA
? High Speed:
300MHz -3dB Bandwidth (MAX4212/MAX4213)
200MHz -3dB Bandwidth
(MAX4216/MAX4218/MAX4220)
50MHz 0.1dB Gain Flatness
(MAX4212/MAX4213)
600V/?s Slew Rate
? Single 3.3V/5.0V Operation
? Rail-to-Rail Outputs
? Input Common-Mode Range Extends Beyond VEE
? Low Differential Gain/Phase: 0.02%/0.02?
? Low Distortion at 5MHz:
-78dBc SFDR
-75dB Total Harmonic Distortion
? High-Output Drive: ?100mA
? 400?A Shutdown Capability (MAX4213/MAX4218)
? High-Output Impedance in Off State
(MAX4213/MAX4218)
? Space-Saving SOT23, ?MAX, or QSOP Packages
MAX4528CPA+
The MAX4528 low-voltage, CMOS analog IC is configured as a phase-reversal switch and optimized for highspeed applications such as chopper amplifiers. It
operates from a 2.7V to 12V single supply or from
?2.7V to ?6V dual supplies.
On-resistance (110? max) is matched between switches to 7? (max). Each switch can handle Rail-to-Rail?
analog signals. The leakage current is only 0.5nA at
25?C and 20nA at 85?C. All digital inputs have 0.8V
to 2.4V logic thresholds, ensuring both TTL- and
CMOS-logic compatibility.
MAX485CPA
MAX481, MAX483, MAX485, MAX487?MAX491, and MAX1487 are low-power transceivers for RS-485 and RS422 communication. Each part contains one driver and one receiver. The MAX483, MAX487, MAX488, and MAX489 feature reduced slew-rate drivers that minimize EMI and reduce reflections caused by improperly terminated cables, thus allowing error-free data transmission up to 250kbps.
The driver slew rates of the MAX481, MAX485, MAX490, MAX491, and MAX1487 are not limited, allowing them to transmit up to 2.5Mbps. These transceivers draw between 120?A and 500?A of supply current when unloaded or fully loaded with disabled drivers. Additionally, the MAX481, MAX483, and MAX487 have a low-current shutdown mode in which they consume only 0.1?A. All parts operate from a single 5V supply.
Manufacturer: Analog Devices Inc./Maxim Integrated
Manufacturer Product Number:MAX485CPA
Description: IC TRANSCEIVER HALF 1/1 8DIP
Detailed Description: 1/1 Transceiver Half RS422, RS485 8-PDIP
max485cpa datasheet
MAX485CSA
The MAX481, MAX483, MAX485, MAX487?MAX491, and
MAX1487 are low-power transceivers for RS-485 and RS422 communication. Each part contains one driver and one
receiver. The MAX483, MAX487, MAX488, and MAX489
feature reduced slew-rate drivers that minimize EMI and
reduce reflections caused by improperly terminated cables,
thus allowing error-free data transmission up to 250kbps.
The driver slew rates of the MAX481, MAX485, MAX490,
MAX491, and MAX1487 are not limited, allowing them to
transmit up to 2.5Mbps.
MAX485ESA
The MAX481, MAX483, MAX485, MAX487?MAX491, and
MAX1487 are low-power transceivers for RS-485 and RS422 communication. Each part contains one driver and one
receiver. The MAX483, MAX487, MAX488, and MAX489
feature reduced slew-rate drivers that minimize EMI and
reduce reflections caused by improperly terminated cables,
thus allowing error-free data transmission up to 250kbps.
The driver slew rates of the MAX481, MAX485, MAX490,
MAX491, and MAX1487 are not limited, allowing them to
transmit up to 2.5Mbps.
These transceivers draw between 120?A and 500?A of
supply current when unloaded or fully loaded with disabled
drivers. Additionally, the MAX481, MAX483, and MAX487
have a low-current shutdown mode in which they consume
only 0.1?A. All parts operate from a single 5V supply.
MAX487CSA
The MAX487E and MAX1487E feature quarter-unit-load
receiver input impedance, allowing up to 128 transceivers on the bus. The MAX488E?MAX491E are
designed for full-duplex communications, while the
MAX481E, MAX483E, MAX485E, MAX487E, and
MAX1487E are designed for half-duplex applications.
For applications that are not ESD sensitive see the pinand function-compatible MAX481, MAX483, MAX485,
MAX487?MAX491, and MAX1487.
MAX489CSD
The MAX481, MAX483, MAX485, MAX487?MAX491, and
MAX1487 are low-power transceivers for RS-485 and RS422 communication. Each part contains one driver and one
receiver. The MAX483, MAX487, MAX488, and MAX489
feature reduced slew-rate drivers that minimize EMI and
reduce reflections caused by improperly terminated cables,
thus allowing error-free data transmission up to 250kbps.
The driver slew rates of the MAX481, MAX485, MAX490,
MAX491, and MAX1487 are not limited, allowing them to
transmit up to 2.5Mbps.
These transceivers draw between 120?A and 500?A of
supply current when unloaded or fully loaded with disabled
drivers. Additionally, the MAX481, MAX483, and MAX487
have a low-current shutdown mode in which they consume
only 0.1?A. All parts operate from a single 5V supply
