89E516RD2

A CMOS 8-bit microcontroller with 20K bytes of Flash programmable read-only memory and 256 bytes of RAM, the AT89C55WD is a low-power, high-performance device. The product is made using high-density flash storage technology from Atmel and has pinout and an instruction set that comply with industry standards 80C51 and 80C52. An ordinary nonvolatile memory programmer can user programme the programme memory thanks to the on-chip Flash. The Atmel AT89C55WD is a potent microcomputer that offers a very flexible and area of business to many embedded control applications by mixing a flexible 8-bit CPU with Flash on a monolithic chip. The following features are included as standard with the AT89C55WD: A full-duplex serial port, an on-chip oscillator, clock circuitry, three 16-bit timer/counters, 32 I/O lines, 256 bytes of RAM, 20K bytes of Flash, and a six-vector, two-level interrupt architecture. The AT89C55WD also features two software-selectable power-saving modes and static logic allowing operating down to zero frequency. The CPU is turned off in idle mode, but the RAM, timers and counters, serial port, and interruption system are still operational. The oscillator is frozen in the Power-down Mode, which also disables all other chip operations until the next error detection or device reset. However, the RAM contents are saved.

A 4K x 8 (32K bit) Serial Electrically Erasable PROM is the 24C32. This gadget was created for high-end, low-power uses like data collecting or personal communications. The 24C32 has an input cache with a capacity of eight 8-byte pages, or 64 bytes, allowing quick write loads. Additionally, it has a fixed 4K-bit block of ultra-high endurance memory for regularly changing data. Up to the 32K border, the 24C32 may read both randomly and sequentially. Up to eight 24C32 devices can share a bus with functional address lines, providing a maximum address space of 256K bits. This device is perfect for moderate POWER  non-volatile code and data applications thanks to advanced CMOS technology. The typical 8-pin plastic DIP and 8-pin surface mount SOIC packaging for the 24C32 are also available.   Features:- • Operating voltage range: 4.5V to 5.5V - Maximum read current: 150 A at 5.5V - Peak write current: 3mA at 5.5V - Typical standby current: 1 A • I2C compliant, industry-standard two-wire bus protocol with 100 kHz and 400 kHz modes • Autonomous write cycle (including auto-erase) • Switchable circuitry for data protection • High Endurance Block has a guaranteed 10,000,000 Erase/Write cycles. - Guaranteed 1,000,000 E/W cycles for Standard Endurance Block • Available in 8 byte page or byte modes. • A 64-byte input cache with 1 page by 8 lines for quick write loads. • Schmitt trigger with filtered inputs to reduce noise • Ground bounce elimination by output slope control • A typical write cycle time, byte or page, of 2 ms • A single bus may support up to 8 chips and 256K bits of total memory. • Protection from electrostatic discharge > 4000V • 200-year data retention • PDIP/SOIC 8-pin packages • Variable temperatures Industrial (I): -40°C to +85°C Commercial (C): 0°C to +70°C

The 1024/2048/4096/8192/16384 bits of serial electrically erasable and programmable read-only memory (EEPROM) provided by the AT24C01A/02/04/08A/16A are structured as 128/256/512/1024/2048 words of 8 bits each. The gadget is designed with a variety of industrial and business applications in mind, where low-power and low-voltage functioning are crucial. The AT24C01A/02/04/08A/16A is accessible through a Two-wire serial interface and is offered in compact 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead MAP, 5-lead SOT23 (AT24C01A/AT24C02/AT24C04), 8-lead TSSOP, and 8-ball dBGA2 packages. There are other variants of the complete series in 2.7V (2.7V to 5.5V) and 1.8V (1.8V to 5.5V) voltage ranges. Features Low and Standard Voltage Operation: 2.7 (VCC = 2.7 to 5.5 V) and 1.8 (VCC = 1.8 to 5.5 V) •128 x 8, 256 x 8, 512 x 8, 1024 x 8, or 2048 x 8 internal organisation (16K) Bidirectional Data Transfer Protocol, Schmidt Trigger, Filtered Inputs for Noise Suppression, Two-wire Serial Interface, and Compatibility at 100 kHz (1.8V) and 400 kHz (2.7V, 5V) 8-byte page (1K, 2K), 16-byte page, Write Protect Pin for Hardware Data Protection (4K, 8K, 16K) Writing Styles •High-reliability– Endurance: 1 Million Write Cycles– Data Retention: 100 Years •Partial Page Writes Allowed •Self-timed Write Cycle (5 ms max) •Automotive Grade and Lead-free/Halogen-free Devices Available •5-lead SOT23,8-lead TSSOP,8-lead PDIP,8-lead JEDEC SOIC,8-lead MAP, and 8-ball dBGA2 Packages •Die Sales: Bumped Wafers, Waffle Packs, and Wafer Forms

The HT9200A/B tone generators are intended for use with C interfaces. aC can direct them to generate 16 dual tones and 8 single tones using the DTMF pin. The HT9200A has a serial mode, but the HT9200B has a selectable serial/parallel mode interface for a variety of applications such as surveillance systems, building automation, navigation system through telephone lines, communication systems, and so on.