PIC24HJ64GP502T-QFN-28
? 10/12-bit ADC with 1.1Msps/500 ksps conversion
rate:
- Up to 13 ADC input channels and four S&H
- Flexible/Independent trigger sources
? 150 ns Comparators:
- Up to two Analog Comparator modules
- 4-bit DAC with two ranges for Analog Comparators
? Parallel Master Port (PMP)
? Two UART modules (10 Mbps)
- Supports LIN 2.0 protocols
- RS-232, RS-485, and IrDA? support
? Two 4-wire SPI modules (15 Mbps)
? Enhanced CAN (ECAN) module (1 Mbaud) with
2.0B support
? I2C module (100K, 400K and 1Mbaud) with
SMBus support
PM8909
Potentiometer 2k 3590S 202
PTS645SH50SMTR9
Electrical
CONTACT RATING: 50 mA @ 12 V DC.
DIELECTRIC STRENGTH: 250 V AC min.
CONTACT RESISTANCE: 100 mā¦ max. initial.
INSULATION RESISTANCE: 10 ā¦ min.
Environmental
OPERATING TEMPERATURE: -20 ĢC to 60 ĢC
Mechanical
ACTUATION FORCE: PTS645 models: 130 grams, 160 grams,
200 grams, 260 grams
LIFE EXPECTANCY: 100,000 operations.
Specification
FUNCTION: Momentary action
CONTACT ARRANGEMENT: SPST, N.O.
TERMINALS: PC pins
Process
SOLDERING: Preheating to 100 ĢC for 45 sec. max. Keep flux flush
with top surface of PCB; do not apply to component side of PCB
and area where terminals are located. Soldering to 255 ĢC for 5 sec.
max. Clean by brushing on solder surface. Do not clean switch with
solvents.
Packaging
Bulk packaging.
Tape & reel for the SMT type:
Reel of 1,000 pieces
QC962-8A
QC962?is a hybrid integrated IGBT driver designed for driving N-channel IGBT modules in any gate amplifier application. The device provides the required electricalisolation between input and output with the opto-coupler. Short circuit protection is provided by a built-in desaturation detector. A fault signal is provided if the short circuit protection is activate.
QC962 IGBT Gate Driver?Features:-
- Built in high CMRR opto-coupler (CMR: Typical: 30kV/?s, Min.:15kV/?s)
- Two supply drive topology
- TTL compatible input interface
- Electrical isolation voltage between input and output with opto-couplers (Viso=3750VRMS/min)
- Built in short circuit protection circuit with in for fault output
- Soft IGBT turn-off and protection circuit time reset
- Controlled time detected short circuit
- Switching frequency up to 20kHz
- Pin and characteristic are compatible with M57962AL
QC962 IGBT Gate Driver?Applications:-
- General-purpose Inverter
- AC Servo Systems
- Unint erruptable Power Supplies(UPS)
- Welding Machines
QCA4020-0-217MSP-TR-0D-0
Features of QCA4020
- The QCA4020 tri-mode SoC combines 802.15.4, dual-band Wi-Fi, and Bluetooth 5 technologies.
- Low power, isolated 15.4 SW MAC, 15.4 and BLE drivers, coex management, and Wi-Fi operations processors (QCA4020 only)
- Secure boot, trusted execution environments, encrypted storage, key provisioning, and wireless protocol security are all features of cutting-edge hardware-based security.
- a full range of interfaces and peripherals, including SPI, UART, PWM, I2S, I2C, SDIO, ADC, and GPIOs.
- Low power sensor use cases are made possible by an integrated sensor hub for post-processing.
- Reduced package size enables improved form factors.
- Package Type - 11.2 x 11.2mm, 0.65mm pitch, 217-ball BGA (QCA4020)
- Application CPU : 1. Arm Cortex-M4F @ up to 128MHz 2. 32KB- L1 cache controller, XIP from external S-flash 3. Internal Memory: 300+KB RAM reserved for applications
- Connectivity/System CPU : 1. Dedicated processor for Bluetooth LE LC and 15.4 MAC 2. Dedicated processor for 802.11 a/b/g/n 3. Isolated Memory: RAM, ROM
- Low Power Bluetooth & 15.4 (Separate radios) : 1. Bluetooth v5.0, PA =+4dBm/+10dBm (for Long Range) 2. 802.15.4: 2006 compliant, 15.4e, 2.4GHz DSSS 3. +4dBm/+21dBm (for Long Range)
- Wi-Fi (QCA4020 only) : Dual Band, 1x1, HT20, MCS0-7, 2.4/5GHz, PA=+18dBm
- Sensor Hub : Low power HW+App CPU, Interface: I2C, SPI, ADC
- Display : Segmented or character display with SPI or I2C interfaces
- Interfaces : 1. 2C, UART, SPI/Q-SPI, ADC (8ch, 12-bit 1Msps) 2. PWM, SDIO2.0, USB2.0 HS, I2S, GPIOs
- Security 1. Secure boot, Secure Storage, HW Crypto Engine 2. HW ECC, 16-bit true random number generator 3. Trusted Execution Environment
- Direct Battery Connection : 1.8V-3.6V
REF01 IC – 10V Precision Voltage Reference IC
The REF01 is industry-standard precision voltage references. The stable 10V output of the REF01 can be adjusted over a ?6% range with minimal effect on temperature stability. The 10V REF01 has a single-supply operation over an input voltage range of 13V to 33V. The devices offer a low-current drain of 1mA.
