LP5907MFX-3.0/NOPB
Features of LP5907MFX-3.0
? 2.2 to 5.5 volts of input voltage
? 1.2 to 4.5 volts in the output voltage range
? Stable with ceramic input and output capacitors rated at 1 F
? No need for a noise bypass capacitor
? Location of the remote output capacitor
? Protection from thermal overload and short circuit
? Operating junction temperature range of -40?C to 125?C
? Low noise output voltage: 6.5 VRMS
? PSRR at 1 kHz: 82 dB
? Tolerance for output voltage: 2%
? Exceptionally low IQ: 12 A
? Minimal dropout (120 mV)
Applications of LP5907MFX-3.0
- Smartphones
- ?Tablets
- ?Communications equipment
- Digital still cameras
- Factory automation
LPC1768 Microcontrollers – MCU
CPU frequencies of up to 100 MHz are supported by the LPC1768/67/66/65/64/63. The LPC1769 can run at CPU speeds of up to 120 MHz. The Arm Cortex-M3 CPU has a three-stage pipeline and a Harvard architecture, with separate local instruction and data buses and a third bus for peripherals. An inbuilt prefetch unit that facilitates speculative branching is also included in the Arm Cortex-M3 CPU.The LPC1769/68/67/66/65/64/63's peripheral complement includes up to 512 kB of flash memory, 64 kB of data memory, Ethernet MAC, USB Device/Host/OTG interface, 8-channel general-purpose DMA controller, 4 UARTs, 2 CAN channels, 2 SSP controllers, SPI interface, 3 I2C-bus interfaces, 2-input plus 2-output I2S-bus interface, 8-channel 12-bit A
LPV358MM/NOPB
Part Number:LPV358MM/NOPB
Mfr.:Texas Instruments
Description: Operational Amplifiers - Op Amps Gen Purp Low Vtg Low Pwr RRO Op Amp
LPV321-N Single, LPV358-N Dual, and LPV324-N Quad General-Purpose, Low Voltage,Low Power, Rail-to-Rail Output Operational Amplifiers.
The LPV358MM are low power (9-?A per channel at 5 V) versions of the LMV3xx op amps. This is another addition to the LMV family of commodity op amps. The LPV3xx-N are the most cost effective solutions for the applications where low voltage, low power operation, space saving and low price are needed.
The LPV358MM have rail-to-rail output swing capability and the input common-mode voltage range includes ground. They all exhibit excellent speed-power ratio, achieving 152 kHz of bandwidth with a supply currentof only 9 ?A.
LPV358MM/NOPB Datasheet
LT1004IS8-1.2
The micropower voltage reference is a
2-terminal bandgap reference diode designed to provide
high accuracy and excellent temperature characteristics
at very low operating currents. Optimization of the key
parameters in the design, processing and testing of
the device results in accuracy specifications previously
attainable only with selected units. Below is a distribution
plot of reference voltage for a typical lot of LT1004-1.2.
Virtually all of the units fall well within the prescribed
limits of ?4mV.
The LT1004 is a pin-for-pin replacement for the
LM185/LM385 series of references with improved accuracy specifications. More important, the LT1004 is an
attractive device for use in systems where accuracy was
previously obtained at the expense of power consumption and trimming.
LT1009CZ
The LT?1009 is a precision trimmed 2.5V shunt regulator diode featuring a maximum initial tolerance of only
?5mV. The low dynamic impedance and wide operating
current range enhances its versatility. The 0.2% reference
tolerance is achieved by on-chip trimming which not only
minimizes the initial voltage tolerance but also minimizes
the temperature drift.
Even though no adjustments are needed with the LT1009,
a third terminal allows the reference voltage to be adjusted
?5% to calibrate out system errors. In many applications,
the LT1009 can be used as a pin-to-pin replacement of the
LM136 and the external trim network eliminated.
LT1013CN8
Single Supply Operation
Input Voltage Range Extends to Ground
Output Swings to Ground While Sinking Current
n Pin Compatible to 1458 and 324 with Precision Specs
n Guaranteed Offset Voltage: 150?V Max
n Guaranteed Low Drift: 2?V/?C Max
n Guaranteed Offset Current: 0.8nA Max
n Guaranteed High Gain
5mA Load Current: 1.5 Million Min
17mA Load Current: 0.8 Million Min
n Guaranteed Low Supply Current: 500?A Max
n Low Voltage Noise, 0.1Hz to 10Hz: 0.55?VP-P
Low Current Noise?Better than 0P-07, 0.07pA/?Hz
LT1017IS8
Maximum Offset Voltage: 1mV
n Maximum Bias Current: 15nA
n Typical Output Drive: 70mA
n Operates from 1.1V to 40V
n Internal Pull-Up Current
n Output Can Drive Loads Above V
n 30?A Supply Current (LT1017)
110?A Supply Current (LT1018)
n Available in 8-Lead PDIP, 8-Lead Plastic S0, and
16-Lead Plastic SO Packages
LT1019ACN8-2.5
LT1019ACN8-4.5
The LT1019 can both sink and source up to 10mA and can
be used in either the series or shunt mode, allowing the
reference to operate with positive or negative output
voltages without external components. Minimum input/
output voltage is less than 1V in the series mode, providing
improved tolerance of low line conditions and excellent
line regulation.
LT1019CN8-2.5
LT1021DCS8-5
The LT1021 references are based on a buried zener diode
structure that eliminates noise and stability problems
associated with surface breakdown devices. Further, a
subsurface zener exhibits better temperature drift and
time stability than even the best bandgap references.
Unique circuit design makes the LT1021 the first IC
reference to offer ultralow drift without the use of high
power on-chip heaters.
The LT1021-7 uses no resistive divider to set output
voltage, and therefore exhibits the best long term stability
and temperature hysteresis. The LT1021-5 and LT1021-
10 are intended for systems requiring a precise 5V or 10V
reference with an initial tolerance as low as ?0.05%.
