SKY13374-397LF

Features of CC2650F128RHB

• Microprocessor - Strong ARM Cortex-M3 processor - 142 for EEMBC CoreMark® - Maximum Clock Speed of 48 MHz - 128 KB of programmable in-system flash - Cache: 8KB of SRAM - 20KB of SRAM with ultra-low leakage. - JTAG and 2-Pin cJTAG Debugging - Facilitates Over-The-Air Upgrade (OTA)
• Sensor Controller with Ultralow Power - Can Operate Independently of the Rest of the System - 16-Bit architecture - 2KB of SRAM with extremely minimal leakage for code and data.
• Packages Compliant with RoHS - RSM VQFN32, 4-mm x 4-mm (10 GPIOs) - RHB VQFN32, 5-mm x 5-mm (15 GPIOs) - RGZ VQFN48, 7-mm x 7-mm (31 GPIOs)
• Peripherals - Any GPIO Can Be Used to Route All Digital Peripheral Pins - Four modules for general-purpose timers. - 200 ksamples/s, 8-Channel Analog MUX, 12-Bit ADC - Comparator for Continuous Time - Ultralow-Power Analog Comparer -Modifiable Current Source - UART - Clock in Real Time (RTC) - Security Module AES-128 - The TRNG (True Random Number Generator) (TRNG) - Depending on the package option, 10, 15, or 31 GPIOs - Eight capacitive-sensing buttons are supported. - Temperature sensor built-in
•  Outside System - Internal On-Chip DC-DC Converter - Low Number of External Components - Complete Integration With Simple LinkTM CC2590 and CC2592 Range Extenders - Compatible with the CC13xx pin of Simple Link - VQFN Packages in 4-mm x 4-mm and 5-mm x 5-mm sizes
• Small Power - Broad Supply Voltage Spectrum • In normal use, 1.8 to 3.8 V • 1.7 to 1.95 V in external regulator mode -5.9 mA Active-Mode RX - Active-Mode TX: 6.1 mA at 0 dBm - 9.1 mA for Active-Mode TX at +5 dBm -MCU in Active Mode: 61 A/MHz -48.5 CoreMark/mA for Active-Mode MCU -8.2 A/MHz Active-Mode Sensor Controller - RAM/CPU Retention and RTC Running: 1 A in Standby - Shutdown 100 nanoamperes (Wake Up on External Events)

Application of CC2650F128RHB

• Electronics for consumers  
• Cellular Phone Accessory  
• Sports and exercise gear  
• Applications for HID  
• Building and Home Automation
• Lighting Management  
• Security and Alarm  
• Labeling Electronic Shelves  
• Nearby tags  
• Health  
• Wireless controls  
• Sensor Networks, Wireless

 

HT12D is a decoder integrated circuit that belongs to 212 series of decoders. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc. It is mainly provided to interface RF and infrared circuits.  They are paired with 212 series of encoders. The chosen pair of encoder/decoder should have same number of addresses and data format.In simple terms, HT12D converts the serial input into parallel outputs. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins. The serial input data is compared with the local addresses three times continuously. The input data code is decoded when no error or unmatched codes are found. A valid transmission in indicated by a high signal at VT pin. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. The data on 4 bit latch type output pins remain unchanged until new is received.

Features of SKY13323-378LF

• Control of positive voltage (0 and 1.8 V to 0 and 5.0 V)
• The frequency range for broadband is 0.1-3.0 GHz.
• Very low insertion loss, typically 0.35 dB at 3 GHz
• High isolation, typical 27 dB @ 3 GHz
• P1dB = +27 dBm, excellent linearity performance
• MLPD (6-pin, 1 x 1 mm, MSL1, 260 °C per JEDEC J-STD-020) ultra-compact packaging

Applications of SKY13323-378LF

• 802.11 b/g WLAN networks
• Wi-Fi repeaters
• ISM-band radios
• Systems for low-power transmission and reception

The MT8880 is a monolithic DTMF transceiver with call progress filter. It is fabricated in Mitel’s ISO2- CMOS technology, which provides low power dissipation and high reliability. The DTMF receiver is based upon the industry standard MT8870 monolithic DTMF receiver; the transmitter utilizes a switched capacitor D/A converter for low distortion, high accuracy DTMF signalling. Internal counters provide a burst mode such that tone bursts can be transmitted with precise timing. A call progress filter can be selected allowing a microprocessor to analyze call progress tones. A standard microprocessor bus is provided and is directly compatible with 6800 series microprocessors.